Showing posts with label carved vessel. Show all posts
Showing posts with label carved vessel. Show all posts

Sunday, October 17, 2010

Three Sisters

three sisters on holiday at the shore
a time away from husbands, work, children
on the boardwalk in a small shop they buy matching hats and dresses
laughing and teasing as they do so, slipping into old familiar roles
after supper they walk barefoot for miles on the beach
arm in arm, leaning into each other, sharing their stories, cherishing each moment
knowing it will never happen again

maple, sycamore, walnut
9-12" tall
they are hollow, the hat crown a friction fit stopper
the dots are inlay
each contains the scent of a different perfume

Sunday, February 14, 2010

Still Spinning

Here is a recent effort in my growing collection of wooden vessels. The concept behind this work is that there would be two vessels. The one that one sees when the piece is still: a narrow cylinder with large top and fins. A spiny blow fish, an artful anemometer, a turbine vessel. The other one is when it is spinning: a virtual one captured only in the mind or with a slow shutter speed. The blur that blends into a smooth solid larger container.
I'm always a little uncertain about work that is more complicated. Simple is usually better, more universally accessible. For this piece I had some nicely figured cherry that I used for the fins. I like the base -  a crotch piece of walnut shaped like a river stone.  There was a lot more engineering for this piece than most I do and that part was fun - reason enough to do it. It spins nicely though a little off center despite considerable effort to get it right on.
Still                                        Spinning

For the technically inclined here is some detail. I ripped the central core as accurately as I could to give me a piece 4 x 4 x 12, marked the centers, then ripped off the corners to give me a long octagon. On the lathe turned the piece but left 1/2' of the octagon at each end. Using the 1/2" as bearing surfaces I ripped the eight slots for the fins on the table saw and then drilled the holes at either end on a horizontal boring setup. The top hole is counterbored and the top turned with a tenon to fit.

The fins are a thin sandwich - 1/8' matched veneers with a 1/16" strip of lead embedded at the edge between pieces. I just had a feeling that I needed weight to overcome the wind resistance of the fins for the piece to spin for any length of time. I thought the weight should be placed at the edge but I don't know why. My physics question is: could I have placed this weight at the core for the same effect?

See the diagram for the method of mounting the piece to spin. Thanks to my friend Jerry for advice. It is basically the way he mounted a weather vane. The main problem I had is that it is difficult to drill a large hole into end grain and the bit drifted off center. So in the end the piece rotates a little off center instead of the dead on Swiss watch perfect I would have liked. I said it was fun I didn't say I did it that well. I'm letting go of this.

Tuesday, September 8, 2009

Bowl of Stone

Bowl of soup. Bowl of fruit. Bowl of stones. Bowl of stone.


Cherry, river stone, 10" x 10" x 4 1/2"
The stone is fixed, a bowl that is never empty.

Thursday, July 30, 2009

A Small Bowl

When you gotta make something you gotta make something. It's a blessing and a curse, the fairly constant stream of ideas and images and possibilities. It's been cultivated over a lifetime I suppose. I go for a while and then there is this pull to try to make one of them; to try to make something beautiful. But working full time and weekend chores doesn't leave a lot of time for it so this time I picked something small, something I thought I might finish with just an hour here and there.

Small Bowl
Walnut 12" x 5" x 4"

This piece went a little differently than my usual pattern. I usually have a well defined idea, maybe drawings and templates that I have done before I start. But this time there was just a rough idea and the piece of wood determined much of what I could do and generated ideas as I went.

Bark beetles bore into trees just beneath the bark leaving tunnel trails in the sapwood. Sometimes a chunk of wood looks fine until you remove some material to reveal these voids. So it was with this piece and with embellishment they became the hieroglyphics on the side - the undecipherable message from another species.

Monday, December 1, 2008

Please Sit Down

"Please Sit Down"

Another vessel. Where do these come from? I'm not sure which might be why I keep making them. Most of the ideas arrive fairly complete and simple drawings and templates are all I do to use as guides. The size is sometimes determined by the wood I have. I'm not sure what wood this is though I think it's hickory. Years ago it was sitting in a pile of other rounds of a tree by the side of the road with a sign that said FREE.

Not always, but often stories about the piece come as the work nears completion just as they might for someone else. This one seems to me to be a combination of elegance and organic funkiness. Maybe it's the filagree or lace-like webbing of the handle and the squat stance. An upper class lady with a lower class past. High tea at the country manor but something sinister is going down.

Monday, October 20, 2008

Walnut Bowl

Walnut Bowl 7 x 6 x 13

Nice to get out in my shop and make something again - it had been a while. Worked on this one and the cherry turning one after the other in a two week span. This one feels a bit chunky to handle, not a sensuous piece, but I think it works in some sculptural ways. Intersecting volumes, planes, and lines. The bowl extending from the block of wood from which it was carved...